#Toyota diagnostic code 51 52 how to#

The horizontal tilt angle value does not match.Д¦7-1 Lifting height switch abnormal Partial rearwheel swing control function Faulty connector Broken connector cableД¦6-1 Abnormal matching measurement value The control mast function is partially restricted. Load indicator does not appear on the display (MFD) The controller is brokenД®rror mode Symptoms on forklift Possible causesД¦2-1 Tilt angle sensor abnormal Mast control function is partially restricted Connector is faultyД¦ 3-1 Tilt lever switch abnormal Mast control function is partially restricted Connector is faultyД¦4-1 Lift lock solenoid abnormal Fork won't come down Connector is brokenД¦5-1 Tilt control solenoid abnormal Forward tilt cannot operate, but Connector is damagedД«ackward tilt operable. Broken connectorД¦1-2 Control mast function is partially restricted Connector cable is damagedДrive control function is limited (MFD opt) Load sensor is faulty Broken connectorД¦1-1 Load sensor abnormal Rear wheel swing control is limited.

Broken connectorДҐ4-1 Swing lock solenoid abnormal Rear wheel swing control is limited. Steer knob is not in position Speed sensor is brokenДҐ2-1 Yaw rate sensor abnormal Rear wheel swing control is limited. Each error code and the time at which it occurred are displayed alternately at 2Д¤1-1 Matching connector abnormal Only the Connector display is faultyДҐ1-1 Speed sensor abnormal Speed indicator keeps showing 0 km/h Connector is faultyДҐ1-2 Rear wheel swing control Damaged connector cable and error code are displayed each time the knob switch is pressed and released.

#Toyota diagnostic code 51 52 how to#

For how to display the main menu, refer to (1) From the main menu, display the diagnosis memory menu. Here the display method using the hour meter and tilt lever is described. Diagnosis memory display method To display the diagnosis memory display, there are a method using the hour meter and tilt lever, a method using the optional display, and a method using a

When this happens, stop the vehicle immediately and check the error code.Дў. Travelling or performing meterials handling operations, an error code is displayed and the lamps turn on as a warning. With the ignition key switch ON, if an abnormality is detected when the vehicle is stopped,

The lamp lights once to allow checking for the bulb, and then turns off again if the status is normal. When the ignition key switch is turned ON, Diagnosis display method The diagnosis is displayed by means of an error code as shown in the illustration to the left, and by the lights turning on. For each possible repair, the estimated cost of repair includes the cost of the relevant parts and the cost of labor required to make the repair.1. Consider replacing the ECM, or taking it to a shop for further diagnosis.ДЇor error code P0134, one or more of the below repairs may be needed to solve the underlying issue. If continuity exists, and you have already replaced the O2 sensor, there is a possible internal fault of the ECM.Check the wire from ECM to the O2 sensor for continuity.If this reading isnвЂ™t within spec, consider replacing the O2 sensor 1 on bank 1 1-.95V with the engine running at operating temperature. Check for any exhaust leaks between the engine and the O2 sensor.Replace vacuum lines or intake air tube if there are signs of cracks or disconnections.

Also, check the connector for good connection and no corrosion.

Visually inspect wiring at the O2 sensor for fray or breakage.

Check to see if there are any other codes along with P0134, and clear your Check Engine Light with FIXD.

Tools Needed to Diagnose Code P0134:Дifficulty of Diagnosis and Repair вЂ“ 2 out of 5 Prematurely replacing the oxygen sensor when the issue lies within the wiring or connectors which could have been diagnosed by a visual inspection. The most common impact of this trouble code is a decrease in your vehicleвЂ™s fuel economy. While this trouble code will likely not prevent your vehicle from running, over time it could cause damage to the catalytic converter, which could affect your vehicleвЂ™s ability to run cleanly and efficiently.

Poor connection at the O2 sensor connector.

*No noticeable adverse conditions in some cases What Is the Cause of Code P0134? This error in the oxygen sensor causes the ECM to misread the amount of oxygen and fuel coming through the exhaust, which inhibits it from ensuring the optimal fuel ratio. The Engine Control Module (ECM) detects that the Oxygen (O2) sensor is at a standstill and is not accurately reading the amount of oxygen in the exhaust. O2 Sensor Circuit No Activity Detected (Bank 1, Sensor 1) What Does P0134 Mean?Д¬ode P0134 is triggered when your vehicleвЂ™s O2 sensor (bank 1, sensor 1) is malfunctioning.